Send Email
Send SMS
Search
Chamak Paint Industries
Chamak Paint Industries


Paint

Leading Manufacturer of clear glossy and matt(wood finish), epoxy redoxide zinc phosphate primer, clear glossy and clear matt wood finis, automotive paint nc finish, clear glossy & clear matt(polyurethane coating) and automotive paint(polyurethane coating) from Ahmedabad.

Clear Glossy and Matt(Wood Finish)

REQUEST CALLBACK

Clear Glossy and Matt(Wood Finish)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth and Glossy
Covering Capacity12 to 14 sq. mt/lit/coat depending upon surface and spraying loss 20 micron DFT.
Flash PointAbove 25 deg C
Packing20 lit, 10 lit, 4 lit, 1 lit, 500 ml
Thinner RecommendedCHAMAK N.C. Thinner 199, CHAMAK N.C. Thinner 111
Method of ApplicationBy Spray @ 45 p.s.i

This is one pack fast drying Nitrocellulose(clear) Lacquer formulated incorporating selected grades of Nitrocellulose, special non-oxidising resins, plasticizers etc. It has very good water, petrols and lub, oil resistance.

Recommended Use:
  • As a finishing clear varnish (Lacquer) on wood. As a finishing top coat for cars, two-wheelers, transport vechicles, light engineering ("white-goods'') product etc. Can be used for mixing in N.C. paints.

Direction for Use:
  • Remove dirt, oil-greese, dust etc. from the subtrate. Clean the surface thoroughly. Adjust the viscosity of clear lacquer to about 18 sec. by FC-84 using recommended thinner.

Drying:

  • Surface Dry: 5 minutes
  • Hard Dry: Approx 5 hours.

Note:

  • During high humid climate, use up to 25 % NC Retarder to minimise blushing.
Yes! I am interested

Epoxy Redoxide Zinc Phosphate Primer

REQUEST CALLBACK

Epoxy Redoxide Zinc Phosphate Primer
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorRedoxide/Grey
FinishSmooth and Samimatt
Mixing RatioBase, Catalyst-3: 1 by volume
Covering Capacity on smooth mild steel surface9 to 10 sq./ mt/ltr for 25 micron dry film thiskness.
Maturation Time30 minutes
Pot life of mixture5 to 6 hours at 30 deg C
Overcoating FinishChlorinated rubber paint and epoxy two pack product after 24 hours drying.
Flash PointAbove 28 deg C(75 deg C)
Thinner RecommendedCHAMAK Epoxy Thinner
Packing20 lit, 4 lit and 1 lit.

It is two pack airdrying epoxy composition with Redoxide and Zinc Phosphate pigment. This primer provide higher degree of protection from corrosion than conventional primer, especially in highly corrosive environment. The primer can be overcoated with conventional painting system, chlorinated rubber and epoxy.

Recommended Use:
  • Recommended for application on structural steel equipments, storage tanks, etc. from chemical and saline environments such as fertilizer units, hydroelectric projects, refineries, chemical processing unit, pulp, paper and sugar factories etc.

Direction for Use:
  • Surface should be clean, free rust, grease, oil, moisture and loose flakes. Sand blast mild steel substrate. Stir the contents before use. Mix base and hardner properl in the recommended ratio. Allow mixture to mature for 30 minutes before appling by brush or spray. Use if necessary recommended thinner. Primed surface should not be exposed to corrosive environment for a long time without application of finishing paints.

Drying Time:
  • Surface Dry-30 minutes
  • Hard Dry- Overnight
  • Overcoating interval-24 hour minimum and 3 day maximum
Yes! I am interested

Clear Glossy and Clear Matt Wood Finis

REQUEST CALLBACK

Clear Glossy and Clear Matt  Wood Finis
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Packaging Size (ex. 1L or 1Kg)20 lit, 4 lit, Hit 6 500 ml
ThinnerCHAMAK melamine Thinner for CHAMAK natural finish
Mixing RatioBase to Hardner in 9 : 1 by volume
Curing Time30 minutes
Recommended UseFor application on wood
RecoatingAfter overnight
FinishSmooth and either Glossy or Matt.
Flash PointAbove 15 deg C
Covering Capacity9 Sq. meter/litres per coat by brush 6 Sq. meters/liter per coat by spray 22 to 25 micron dry film t

This is a specialised product from CHAMAK in two pack system of Base and Hardner. CHAMAK is available as Clear Glossy or as
Clear Matt. This premium coating with melamine protects wood for years together for Melamine wood finish, water, insect attack etc. As clear satin shows excellent resistance to satin from edible oil and fats, foods, hot beverages.

Application Viscosity:
  • For brushing: 25 to 30 sec. by Fc4 @ 30 deg C
  • For spraying: 20 to 30 sec. by Fc4 @ 30 deg C

Drying Time:
  • Surface dry: Approx. 30 minutes
  • Hard dry: Approx. 15 to 20 hours

Directions:
  • Sand the wood surface along the grains with suitable sand paper. Wipe the surface clean free of loose dust. Now fill the surface with wood filler N-C Sanding sealer after 2/3 hours of drying, sand it again with emery paper no. 320. Again ensure that surface to be coated is free loose dust etc. Now take out CHAMAK Base and CHAMAK Hardner in glass or plastic or enameled container and mix them in 9:1 ratio (by volume). Let the mixture stand for 30 minutes for cure. Now apply by brush or spary using recommended thinner. Use the mixture within 8 hours. After 48 hours of application buff tlie surface with buffing mops to enhance gloss if CHAMAK Clear Glossy is applied.
Yes! I am interested

Automotive Paint NC Finish

REQUEST CALLBACK

Automotive Paint NC Finish
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Packing20 liters. 4 litres. 1 liter. 500 mis
ColorAs per shade card including white, Ref. White S.J Black Aluminium and Matt Black
FinishSmooth and Glossy
Drying TimeSurface dry 5 minutes. Hard dry -1 to 2 hours
Flash PointAbove 25 deg C (75 deg F)
Thinner RecommendedCHAMAK N.C. Thinner No 199/111
Method of ApplicationBy spray at pressure of 40 to 50 P.S.I
Recommended PrimerCHAMAK N.C.P.S Grey
Shelfe LifeAs long as container is kept sealed it can; be stored upto 12 months without deteriorat

This in one pack quick drying nitrocellulose base paint, it is formulated in acordance with the laest development in the lacquer industry. It is based on selected grades of nitrocellulose, high grade if non oxidising resin and plastisizer. it is pigmented with hight capacity. light fast pigment to produce to produce high gloss, hard flexible and durable film. It has very good water petrol, and lubricating oil resistance. It has very good rubbing properties. The metallic shades give a duel tone effert and are extermerly brilliant, glossy and durable.

Recommended Use:
  • It is used for automobiles, two-wheelers, transport vehicles and engineering good, fans, refrigerators, etc.

Direction for Use:
  • Remove dirt, grease, oil, dust. Clean the surface property. Adjust the visosity of lacquer to 18 sec. By F.C. No.4 with Chamak N.C. Thinner no 199/111 ensure that chamak P.S.applied over the body has throughly dried and has been sanded down propely spray 2 to 3 coats of lacquer at a pressure of 40 to 50 PSI at an intervak of 10 to 15 minutes between coats. Airdry overnight scuff the surface with no. 400 wet or dry silicon carbide paper using soap and water. Clean the surface with water, dry it and spray one flow coat of lacquer by mixing one part 15 sec. by F.C.No 4. Air dry overnight. Burnish with std. made rubbing compound. followed by polish with std.made wax polish. After painting with Chamak Autoprimer paints regular washing and using of silicon polish or wax polish is enough to maintain the original gloss and colour of the paint for years. Stir the content thoroughly prior to use.

Special Instruction:
  • To minimise blusing when spraying Chamak Aluminium paints during rainy seaon, use upto 25% CHAMAK Retarder.

Covering Capacity on Smooth Mild Steel Surface:
  • 12 to 13 sq. mt/it./Coat depending upon surface and spiaying loss (cars 4 to 5 litres scooters 1 to. 1.5 liters depending upon models. For 30 micron dry film thickness.
Yes! I am interested

Clear Glossy & Clear Matt(Polyurethane Coating)

REQUEST CALLBACK

Clear Glossy & Clear Matt(Polyurethane Coating)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Recommended UseFor application on wood and metal
ThinnerCHAMAK PU-thinner
Mixing RatioBase to Hardner in 3: 1 by volume
Curing Time30 minutes
FinishSmooth and either Glossy or Matt.
Flash PointAbove 25 deg C
Packing20 lit, 4 lit, 1 lit

This is specialised product from CHAMAK in two pack system of Base and Hardner CHAMAK Polyurethane coating is available as Clear Glossy and as Clear Matt finish. The premium coating protects wood and metal form heat, water, insect, alkali, ultraviolet attack etc. It shows excellent resistance to satin from edible oil and fats, foods, hot beverages.

Drying Time:
  • Surface dry: Approx. 30 minutes
  • Hard dry: Approx. 12 to 15 hours
  • Recoating: After 4-5 hours

Covering capacity:
  • 9 Sq. meters/litres per coa by brush
  • 6 Sq. meters/liter per coat by spray

Application Viscosity:
  • For brushing: 25 to 30 sec. by Fc-4 @ 30 deg C
  • For spraying: 20 to 30 sec. by Fc-4 @ 30 deg C

Directions:
  • Sand the surface along the grains with suitable sand paper. Wipe the surface clean free of loose dust. Now fill the surface with wood filler, Sanding sealer. After 2/3 hours of drying, sand it again with the suitable paper. Again ensure that surface to be coated is free loose dust etc. Now take out CHAMAK base and hardner in glass or plastic or enameled container and mix them in 3:1 ratio (by volume). Let the mixture stand for 30 minutes for cure. Now apply by brush or spary, using recommended thinner. Use the mixture within 4 hours. After 48 hours of application buff the surface with buffing mops to enhance gloss if CHAMAK Clear Glossy is applied.
Yes! I am interested

Automotive Paint(Polyurethane Coating)

REQUEST CALLBACK

Automotive Paint(Polyurethane Coating)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth and Glossy
Colour AvailableWhite, Black, Cream, Green, Gray, Red, etc.
Covering Caparity on Smooth Mild Steel Surface 10 to 12 sq. mt/ ltr. For 30 micron dry film thiuckner
Mixing RatioBase to Hardner 3 : 1 by volume
Thinner Recommended Chamak PU - Thinner
Curing Time 30 Minutes
Recoating After 4 -5 hours
Flash Point Above 25 deg C
Packing 20 lit, 4 lit, 1 lit

This is specialised product from CHAMAK in two packs system of Base and hardener. It is formulated in accordance with the latest development in the lacauer industry. It is based on selected Grades of polyurathane, high grade of non axiding resin. It is pigmented with high capacity, Light fast pigment to produce high gloss, hard flexible and durable film. It has very good Water, Petrol and Lubricating Oil resistance. It has very good rubbing properties and durabality.

Recommended Use:
  • It is used for auto mobiles, two wheelers, transport vechiles and enginneering goods, fans, refrigerators, machineries etc.

Drying Time:
  • SD approx 30 minutes HD
  • HD – approx 12-15 hours

Application Viscosity:
  • For brushing -25 ot 30 sec. By FC -4 @ 30 deg C
  • For spraying -20- 25 sec. By FC-4  30 deg C

Directions for Use:
  • Remove dirt /grease/ oil /dust. dean the surface properly. ensure that CHAMAK primer sufacer applied over the body has throughly dried and has been sanded down property spray 2 to 3 coats. Now take out CHAMAK base and hardner mix them in 3:1 ratio ( by volume ) let the mixture stand for 30 minutes for cure. Now apply by brush or spray using recommended thinner use the mixture within 4 hours.
Yes! I am interested

Primer Surfacer(Polyurethane Coating)

REQUEST CALLBACK

Primer Surfacer(Polyurethane Coating)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth and Matt
Colour AvailbleRedoxide / White / Grey
Covering Capacity on smooth & Mild Steel Surface9 to 10 Sq. Mt/ltr. For 25 micron dry film thickness
Mixing Ratio Bast to Hardener 3:1 by Volume.
Thinner Recommended CHAMAK PU. Thinner
Application Viscosity Form Spray 20 to 25 sec. By FC-4 @30 deg C.
Curing Time 20 minutes
Flash PointAbove 25 deg C
Packing2 lit, 4 lit, 1 lit

It is two pack polyurethane composition. This primer provide higher degree of protection from corrosion than conventional and durable, especially in highly  corrosive conventional painting systems.

Recommended Use:
  • It is used for automobiles, two wheelers, transport vehicles and engineering goods, refrigerators, machineries etc.

Application Viscosity:
  • For Brushing: 25 To 30 Sec. By Fc-4@30°C.
  • For Spraying: 25 To 30 Sec. By Fc-4@30°C.

Drying Time:
  • Surface Dry-approx 20 minutes
  • Hard Dry 6-7 hours
  • Recoating after 3-4 hours.

Directions for Use:
  • Surface should be clean, free, from rust, grease, oil, moisture and loose flakes. Sand blast mild steel substrate. Stir the contents before use. Mix base and hardner properlyl in the recommended ratio. Let the mixtures stand for 20 minutes for cure. Now apply by brush or spray, using recommended thinner. Use the mixture within 3 Hours.
Yes! I am interested

Acid and Alkali Resistance Epoxy Enamel(Epoxy Coating)

REQUEST CALLBACK

Acid and Alkali Resistance Epoxy Enamel(Epoxy Coating)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth and Glossy
Full CureMinimum 7 Hays at 30 deg C
Flash PointAbove 25 deg C (75 deg F)
Packing20 liters. 4 liters and 1 liter
Colour AvailableWhite, Black, Cream, Light blue, Light green, Light grey, Dark grey, etc.
Covering Capacity on Smooth Mild Steel Surface 9 to 10 sq. mL/lt, for 40 micron dry film thickness
Thinner Recommended Chamak Epoty thinner
Mixing RatioBase to Catalyst - 3 : 1 by volume
Maturation Time 30 minutes
Overcoating Time24 hours minimum and 5 days maximum

CHAMAK epoxy enamel is two pack airdrying epoxy resin composition suitably pigmented. it is extremely tough high performance coating. This product has excellent resistance to solvents, chemicals with desocrative appeal. It has good flexibility and adhesion.

Other details:
  • Excellent Acid & Alkali Resistance
  • Excellent Abrasion & Scratch Resistance
  • Good looking as Matt, Satin & Glossy Finish

Recommended Use:
  • It is used in tanks, chemical plants, oil refineries, fertilizer complexes, etc. where outstanding chemical resistance is essential. it is also recommended as floor coating in Locations where chemical splashes, petrol spillage etc, It is also suitable for tea fermentation floor, laboratory furniture, etc.

Recommended Primer:
  • Chamak Epoxy Zinc Phosphate Red Oxide Primer
  • Chamak Epoxy Zinc Chrome Primer Yellow

Pot Life of Mixture:
  • Surface Dry - 30 to 40 minutes.
  • Hard Dry - Overnight.

Self Life:
  • As long as morello' remaining unmixed and containers are kept firmly seated, it can be stored upto six months without deterioration.

Direction for Use:
  • Remove dust, oil, grease, moisutre and loose flakes, etc. Sand blast mild steel surface. Prime and surface with recommended primer, after overnight drying, sand with emery paper. Mix base and hardner in the recommended ratio and allow to molure for 30 minutes. Apply by brush or spray using recommended thinner. For spray application apply a mist coat, allow to dry for about 10 minutes and then apply full spray coat. Stir the contents thoroughly before use.
Yes! I am interested

Epoxy Redoxide Zinc Phosphate Primer

REQUEST CALLBACK

Epoxy Redoxide Zinc Phosphate Primer
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth and Samimatt
Thinner RecommendedChamak Epoxy Thinner
Packing20 lit, 4 lit & 1 lit
Colour Redoxide/ Grey
Covering Capacity on Smooth Mild Steel Surface9 to 10 Sq. mt./ltr for 25 micron dry film thickness
Mixing RatioBase: Cataiyst-3 : 1 by volume
Maturation Time30 Minutes
Pot life of mixture5 to 6 hours at 30 deg C
Method of ApplicationBrush of spray at a pressure of 40 to 50 PSI.
Overcoating FinishChlorinated Rubber paiint and epoxy two pack products after 24 hours drying

It is two pack airdrying epoxy composition with Redoxide andZinc phosphate Pigment. This primer provide higher degree of protection fro corrosion than Conventional primers, especially in highly Corrosive environements. This primer can be overcoated with conventional painting  systems, chlorinated rubber and epoxy.

Recommended Use:
  • Recommended for application on structural steel equipments, storage Tanks etc.from chemical and saline environments such as fertilizer units, hydroelectric projects, refineries, chemical processing units, pulp, paper and sugar factories etc.

Drying Time:
  • Surface Dry-30 minutes.
  • Hard Dry- Overnight.
  • Overcoating Interval -24 Hours minimum and 3 days maximum.

Direction for Use:
  • Surface should be clean, free rust, grease, oil, moisture and loose fates. Sand blast mild steel substrate. Stir contents before use. Mix base and Hardner Property in the recommended ratio. Allow mixture to mature , before applying by bursh or spray. Use if necessary recommended Thinner. Primed surface should not be exposed corrosive environment for a long Time without application of finishing paint. In case the primer coat dries for more than a week sand papering of prime coat is necessary before application of finishing paints for good inter coat adhesion.
Yes! I am interested

N.C. Putty (Trowling Compound)

REQUEST CALLBACK

N.C. Putty (Trowling Compound)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth & Matt
Colour Grey
Flash Point Above 25 deg C (75 deg F)
Consistency Smooth and butter cut.
Thinner Recommended CHAMAK N.C. Thinner No. 111/199
Method of ApplicationBy Putty Knife
Recommended Primer CHAMAK AUTO Primer or CHAMAK N.C. High Build P.S.Grey.
Packing 20 litres, 4 litres, 1 litre, 500 mls.

CHAMAK N.C. Putty is airdrying Nitrocellulose, non oxidising Resin & Filler base putty, it has butter like consistency. It can beapplied by putty knife. It is supplied ready to use consistency. It can be thinned to desired consistency by using recommended thinner, it dries hard. Its cutting is easy. It is used for filling dents and other surface imperfections.

Recommended Use:
  • After application of recommended primer, it is used metallic and wooden surfaces for filling surface imperfections and dents. It is recommended for cars, scooters, truck bodies, furnitures and table tennis top, etc.

Drying Time:
  • Surface Dry - 5 minutes.
  • Hard Dry - 2 to 3 hours.

Direction for Use:
  • Remove dirt, oil, grease, moisture and loose flakes. Surface shall be primed with recommended primer. Apply thin coats of CHAMAK N.C Putty with putty knife whereever is necessary with 15 to 20 minutes flash off between coats. Deep dents shall be filled in thin layers. After through drying, wet sand with suitable waterproof sand paper and apply CHAMAK P.S Grey, use recommended thinner if required.

Shelf Life:
  • As long as containers are kept sealed it can be stored up to 12 months without deterioration.
Yes! I am interested

N.C.P.S. Grey

REQUEST CALLBACK

N.C.P.S. Grey
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth & Matt
Colour Grey, White & Black
Flash Point Above 25 deg C (75 deg F)
Thinner Recommended CHAMAK N.C. Thinner No. 111/199
Method of Application By spray at a pressure of 40 to 50 P.S.I.
Application Viscosity 20 to 25 sec. by F.C. No. 4 at 30 deg C.
Subsequent Coat CHAMAK Automotive Paint, Classic Car Finish
Packing20 Litres, 4 Litres, 1 Litre, 500 mls.

CHAMAK High Build P.S. Grey is based on Nitrocellulose, nonoxidising resin and ptastisizers. It is one pack, airdrying primer surfacer. It dries fast and hard. It has good adhesion on Primed surfeace. Automotive Paints or Classic car paint can be applied on it.

Recommended Use:
  • It is recommended to apply as a primer surfacer on cars, scooters, trucks, body and transport vehicles.

Covering Capacity on Smooth Mild Steel Surface:
  • 10 to 12 sq. mt./lit/Coat depending upon surface and spaying loss for 25 micron dry film thickness.

Drying Time:
  • Surface Dry - 5 minutes.
  • Hard Dry - 2 to 3 hours.
  • Overcoating interval

Direction for Use:
  • Surface shall be free from rust, grease, oil, moisture, dirt and loose flakes. Apply first CHAMAK Automotive Primer Brown. After thorough drying and sanding with emery paper apply two coats of CHAMAK P.S. Grey using recommended thinner at an interval of 15 to 20 minutes between coats. Dry it overnight. Then apply subsequent coats. Stir the contents thoroughly.

Shelf Life:

  • As long as containers are kept sealed it can be stored upto 12 months without deterioration.
Yes! I am interested

Auto Primer Brown

REQUEST CALLBACK

Auto Primer Brown
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorBrown
Finish Smooth & matt
Covering Capacity on Smooth Mild Steel Surface Dry film thickness depending upon surface and normal
Flash Point Above 24 deg C (75 deg F)
Thinner Recommended N.C. Thinner No. 111/199
Method of Application By Brush or spray at a pressure of 40 to 50 P.S.I.
Subsequent Coat CHAMAK Enamels, CHAMAK P.S. Grey, CHAMAK Putty, etc.
Packing 20 litres, 4 litres. 1 litre, 500 mls

CHAMAK AUTO Primer Brown is based on Syn. Resin. & Anticorrosive pigments. It is ideal for new, pickled, abrasive blasted or slightly rusted steel in production and steel fabricating operations. It is also suited for maintenance or new construction work where fast drying is desired. It is formulated especially for spray application, but may be applied by brush. It dries hard to form a good tough coating. Special feature of this primer is NC base primer & Putty can be applied after hard drying of the primer.

Recommended Use:
  • It is applied on ferrous substrates. On transport vehicles, cars, scooters body, maintenance & new construction work where fast drying is desired.

Application Viscosity:
  • Brushing -50 to 60 sec at 30 C by F.C. No. 4
  • Spraying - 30 to 35 sec at 30 deg C by F.C. No. 4

Drying Time:
  • Surface Dry - Less than 30 minutes.
  • Hard Dry - Less than 16 hours.
  • Overcoating time - Minimum 8 to 10 hours.

Direction for Use:
  • Remove dust, oil, grease, moisure, rust & other loose flakes etc. Apply CHAMAK Auto Primer Brown by adjusting the viscosity with recommended thinner for brusing or spraying. Allow primer coat to hard dry. Sand the primer coat with sand paper & apply subsequent coat. Stirr well prior to use.
Yes! I am interested

Synthetic Enamel (As Per IS 2933)

REQUEST CALLBACK

Synthetic Enamel (As Per IS 2933)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth & Glossy
Colour As per shade card including white and Black.
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended CHAMAK syn. G.P. Thinner
Method of Application By brush or spray at a pressure of 40 to 50 P.S.I.
Packing 20 litres, 10 litres, 4 litres, 1 litres, 500 mls.

CHAMAK Premium Gloss Syn. Enamel is quick drying, with smooth hard & glossy finish. Its dry film has good adhesion to the surface. It has very good flow and brushability

Recommended Use:
  • It is applied on furnitures, drums, barrels, household products, electrical motors, doors, windows and variety of other surfaces which are not subjected to outdoor exposure.

Drying Time:
  • Surface dry - Less than 2 hours.
  • Hard Dry - Less than 15 Hours.
  • Second coat application period - After 10 hours.
  • Above all properties depend upon temperature and humidity.

Covering Capacity on Smooth Mild Steel Surface:
  • 13 to 17 sq. mt. / lt. / Coat at 18 to 20 micron, dry film thickness, depending upon shades and surface.

Recommended Primer:

  • For Metal: CHAMAK Primer Redoxide Metal Primer, CHAMAK Zinc Chrome Redoxide Primer, CHAMAK Zinc Chrone Primer yellow.
  • For Wood: Wood Primer White/Pink
  • For Plaster: CHAMAK Cement Primer (Oil Base).

Application Viscosity:
  • Brushing 50 to 60 sec at 30 deg C by F.C. No. 4
  • Spraying 30 to 35 sec at 30 deg C by F.C. No. 4

Direction for Use:
  • Remove dust, oil, grease, moisture, rust and other loose flakes etc. After priming the surface with recommended primer, with overnight drying & sanding with emery paper, apply CHAMAK Premium Glossy Synthetic Enamel using recommended thinner. Allow first cot to dry for minimum 10 hours before applying second coat. Stir the content thoroughly prior to use.
Yes! I am interested

G.P. Enamel Synthetic Enamel As Per IS 133

REQUEST CALLBACK

G.P. Enamel Synthetic Enamel As Per IS 133
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth & Glossy
Colour As per shade card including white and black
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended CHAMAK syn. G.P. Thinner
Method of Application By brush or spray at a pressure of 40 to 50 P.S.I.
Packing 20 Litres, 10 Litres, 4 Litres, 1 Litre, 500 mls

CHAMAK Synthetic Enamel It general purpose Synthetic Enamel, economically priced, durable finish paint. It is recommended for only interior use. It can be applied by brush or spray to give smooth, hard & glossy finish. It is fast drying. It has very good flow & leveling Properties.

Recommended Use:
  • It can be applied on any surface (metal, wood & Plaster) which are not subjected to Outdoor exposure.

Covering Capacity on Smooth Mild Steel Surface:
  • 8 to 10 sq. mt. / lt. / coat at 18 to 20 micron, dry film thickness, depending upon shades and surface.

Drying Time:
  • Surface dry - Less than 2 hours.
  • Hard Dry- less than 15 Hours.
  • Second coat application period - After 10 hours. (Above all properties depend upon temperature and humidity)

Application Viscosity:
  • Brushing 50 to 60 cec at 30 deg c by F.C. No. 4
  • Spraying 30 to 35 cec at 30 deg c by F.C. No. 4

Recommended Primer:
  • For Metal: CHAMAK PRIME Redoxide
  • Metal Primer: CHAMAK Zinc Chrome Redoxide
  • CHAMAK PRIME Zinc Chrome Primer yellow: CHAMAK P.S. Grey or white.
  • For Wood: Wood Primer White / Pink.
  • For Plaster: CHAMAK PRIME Cement Primer (Oil Base).

Direction for Use:
  • Remove dirt, oil, grease, moisture, rust and loose flakes. After priming the surface with recommended primer. with overnight drying & sanding with emery paper apply CHAMAK Synthetic Enamel uiing recommended thinner. Allow first coat to dry forminimum 10 hours before applying second coat. Stirwell prior to use.
Yes! I am interested

Furniture Enamel Airdrying / Stoving Paint

REQUEST CALLBACK

Furniture Enamel Airdrying / Stoving Paint
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth & Glossy
Flash PointAbove 30 deg C (86 deg F)
Thinner RecommendedCHAMAK syn. G.P. Thinner
Method of ApplicationBy Brush or spray at a pressure of 40 to 50 P.S.I.
Recomended PrimerRedoxide Metal Primer
Packing20 litres, 4 litres, 1 litre 500 mls.

CHAMAK Furniture Enamel is formulated to meet the requirement of painting steel furniture & office equipments. Finish is smooth & glossy with good hardness & adhesion. It can be airdried or can be stoved.

Recommended Use:
  • It is applied on steel cupboard, chairs, tables, etc.

Covering Capacity on Smooth Mild Steel Surface:
  • 12 to 15 sq. mt. / lit. /coat by brush at 20 to 22 micron dry film thickness 10 to 14 sq. mt / lit. Coat by spraying at 18 to 20 micron dry film thickness depending upon shade, surface & spraying loss.

Application Viscosity:
  • Brushing 50 to 60 cec at 30 deg C by F.C. No. 4
  • Spraying 30 to 35 cec at 30 deg C by F.C. No. 4

Drying Time:
  • Surface dry - Less than 2 hour
  • Hard Dry - Less than 15 hours. (Stoving schedule 120 deg C for 30 minutes)

Direction for Use:
  • Remove dirt, oil, grease, moisture, rust & loose flakes. After priming the surface with recommended primer and overnight drying & sanding with emery paper apply CHAMAK Furniture Enamel using recommended thinner. Allow first coat to dry for minimum 10 hours before applying second coat. Stir well prior to use.
Yes! I am interested

Chassis Enamel Paint

REQUEST CALLBACK

Chassis Enamel Paint
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth & Glossy
Colour avalibleBlack, Red & Grey (Tata Steel Grey)
Covering Capacity on smooth Mild Steel Surface13 to 14 sq. mt./lit./coat by brushing for 20 micro
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended CHAMAK syn. G.P. Thinner
Method of Application By brush or spray at a pressure of 40 to 50 P.S.I.
Packing 20 litres, 4 litres, 1 litres & 500 mls

CHAMAK Chassis Enamel is quick drying, economically priced, corrosion resistance glossy paint. It possesses excellent mechanical properties such as impact and abrasion resistance. Electrical insulating properties are also good & very good water resistance.

Drying Time:
  • Surface dry - Maximum 2 hours.
  • Hard dry - Less than 15 hours (Above all properties depend upon temperature and humidity.)

Recommended Use:
  • CHAMAK Chassis Enamel is recommended for coating of motor vehicle chassis for protection from corrosion.

Direction for use:
  • Surface should be free from rust, grease, oil, moisture and loose flakes. Apply by brush or spray using recommended thinner if required. Allow to dry hard before applying second coat. Stir well prior to use.
Yes! I am interested

Interior Wall Finish

REQUEST CALLBACK

Interior Wall Finish
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth with slight sheen
Colour As per shade card including Base white
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended CHAMAK syn. G.P. Thinner
Method of Application By brush, roller or spray at a pressure of 40 to 50 P.S.I.
Packing 20 litres, 10 litres, 4 litres, 1 litres

A Synthetic resin base paint for decoration of interirors of home, sheen helps in reducing dirt pick-up and gives the walls a velvety finish. It is based on highly durable synthetic binder.

Recommended Use:
  • It is ideal for living rooms, dining rooms, balconies, offices and on asbestos, concrete, brickwork and all areas where an attractive flat finish is required.

Covering Capacity on Smooth Mild Steel Surface:
  • 12 to 14 sq. mt./lt./Coat for 22 to 23 micron, dry film thickness depending upon nature of surface and shade.

Drying Time:
  • Surface Dry - Less than 1 hours.
  • Hard Dry - Overnight.

Direction for Use:
  • Remove loose particels and paint flakes. Rub with sand paper. Ensure that the surface is dry and free from dust, dirt. Previous coating of lime wash, powder distemper etc. must be thoroughtly scrapped off. Earlier coating of oil based or synthetic emulsion paint need not be removed, if in sound condition. Howeve, gloss or sheen of such coating must be removed by through sanding. Then apply cement primer (oil base). Use putty for smoothing the surface & filling the dents. Sand with emery paper. Apply again Cement Primer white (Oil Base), sand it and apply two or three coats of CHAMAK wall Finish after drying each coat throughly. This will give you smoothvelvety finish with slight sheen. Use recommended thinner for reducing the viscosity for brushing, roller coating or spraying. Stir the content thoroughly before use.
Yes! I am interested

Quick Set Red Oxide Primer

REQUEST CALLBACK

Quick Set Red Oxide Primer
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorLight Brown
Flash Point Above 25 deg
FinishSmooth and Matt
Application Method By Brush or spray @ 45 P.S.I.
Subsquent Coat CHAMAK Enamels N.C.P.S. Grey, N.C. Putty etc.
Packing 20 lit, 4 lit, 1 lit, 500 mls.

CHAMAK Quick Set Red Oxide Primer based en special synthetic resin & anticorrosive pigments, is idealy suited where fast during is reaired. The film dries hard quickly forming a good tough coat. Notable special feature of this primer is that one can use either enamel system or N.C. system for subsequent coats.

Recommended Use:
  • Applicable Tor ferrous substrate on. Cars, scooters, transport vehicles etc. For new fabrication work and maintenance work where quick drying is essential.

Application Viscosity:
  • Brushing - 50 to 60 sec. @ 30 deg C, by FC4
  • Spraying - 30 to 35 sec 30 deg C. by FC4

Covering Capacity:
  • For Smooth M.S. surface : approx 14 sq. m/lit. per coat @ 20 micron DFT, depending on surface and spaying loss.

Drying Time:
  • Surface dry: Approx 15 minutes
  • Dard dry: Approx 6 hours.

Direction for Use:
  • Remove dust, oil, grease, moisture, etc, from the surface to be coated. Prior degreasing & derusting can also be done. Apply CHAMAK Quick Set R/O Primer by brush or Spray, use recommended thinner for desired viscosity. Allow primer coat to hard dry. Sand the primer coat with sand paper and apply subsequent coats. Stir well perior to use.
Yes! I am interested

Red Oxide Metal Primer

REQUEST CALLBACK

Red Oxide Metal Primer
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth and Matt
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended Synthetic G.P. Thinner
Method of ApplicationBy brush or spray at a pressure of 40 to 50 P.S.I.
Subsequent CoatCHAMAK Enamel or according to specification.
Packing20 litres, 10 litres, 4 litres, 2 litres, 1 litres, 500 mls.

CHAMAK Prime Red Oxide Metal Primer is most economical primer. It has good adhesion & gives fairly good corrosion resistance to metal. It can be brushed or sprayed. It gives hard & tough coating on metal surface

Recommended Use:
  • It is applied on steel furnitures industry cast, iron, and short wherever economical primer is required on ferrous substrates, itcan serve the purpose.

Covering Capacity on Smooth Mild Steel Sruface:
  • 15 to 16 sq. mt./lt. / Coat for 18 to 20 micron dry film thickness by brush depending upon surface.

Application Viscosity:
  • Brushing 50 to 60 sec at 30 C by F.C. No. 4
  • Spraying 30 to 35 sec at 30 deg C by F.C. No. 4

Drying Time:
  • Surface dry - Less than 1 hours.
  • Hard dry - Less than 15 hours.
  • Overcoating time - Minimum 8 to 10 hours. (Above properties depend upon temperature & humidity).

Direction for Use:
  • Remove dust, oil, grease, moisture, rust & other loose flakes etc. Apply Syn. Redoxide primer by adjusting the viscosity with recommended thinner for brushing or spraying. Allow primer coat to hard dry. Sand the prime coat with sand paper & apply subsequent coat.
Yes! I am interested

Synthetic Wood Primer

REQUEST CALLBACK

Synthetic Wood Primer
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorWhite & Pink
Recommended Use On wooden surface
Finish Smooth and Matt
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended Synthetic G.P. Thinner
Method of Application By brush or spray at a pressure of 40 to 50 P.S.I.
Subsequent coat Synthetic Enamels, Under Coats, CHAMAK Interiro wall finish
Packing 20 litres, 4 litres, 1 litres, 500 mls

CHAMAK Wood primer white is a primer to protect wood from swelling due to absoption of moisture. It help preventing blistering on wood. It penetrates, seat & fill the wood fibre & gives very good adhesion to surface. Finishing coat can be applied on this primer easily without absorbing.

Drying Time:
  • Surface dry - Less than 30 minutes.
  • Hard dry - Less than 16 hours.
  • Over coating time - 10 to 12 hours Minimum

Application Viscosity:
  • Brushing - 40 to 50 sec at 30 deg C by F.C. No, 4.
  • Spraying - 25 to 30 sec at 30 deg C by F.C. No, 4.

Covering Capacity on Smooth Surface:
  • 12 to 14 sq. mt. it/Coat for 15 micron dry film thickness depending upon surface by brush.

Direction for Use:
  • Remove dust, oil, grease, moisture & loose flakes. Previous paint it any should be stripped off. Apply one or two coats by adjusting the viscosity with recommended thinner. Allow the prime Coat to hard dry. Dry cut with sand paper before applying subsequent coats. Stir well prior to use.
Yes! I am interested

Cement Primer (Oil Base)

REQUEST CALLBACK

Cement Primer (Oil Base)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorWhite
Finish Smooth and Matt
Flash Point Above 30 deg C (86 deg F)
Thinner RecommendedSynthetic G.P. Thinner
Method of Application By brush or spray at a pressure of 40 to 50 P.S.I.
Subsequent Coat Synthetic Enamels, Under Coats, Wall finish
Packing 20 litres, 10 litres, 4 litres, 2 litres, 1 litres, 500 mls.

CHAMAK Cement Primer (Oil Base) solvent thinable is used for priming Plastered walls, bricks asbestos, concrete to give good sealing properties. Its setting is fast. It has good resistance to water and wall alkalinity.

Recommended Use:
  • Plastered walls, bricks, asbestos, concrete etc. Suitable for interior use. For exterior purpose recommended subsequent coat must be applied over it.

Covering Capacity on Smooth Surface:
  • 12 to 14 sq. mt./lt./Coat for 15 micron dry film thickness depending upon surface & surface preparation by brushing.

Drying Time:
  • Surface dry - Less than 30 Minutes.
  • Hard dry - Less than 16 hours.
  • Over coating time - 10 to 12 hours Minimum

Application Viscosity:
  • Brushing - 40 to 50 sec at 30 deg C by F.C. No. 4.
  • Spraying -25 to 30 sec at 30 deg C by F.C. No. 4.

Direction for Use:
  • Remove all loose flakes. Previous paint should be stripped off. Apply two coats of primer by adjusting the viscosting the viscosity with recommended thinner by brush. Allow prime coat to hard dry. Dry cut with sand paper before applying subsequent coats. Stir well prior to use.
Yes! I am interested

Cement Primer (Water Base)

REQUEST CALLBACK

Cement Primer (Water Base)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorWhite
Finish Smooth and Matt
Thinner Recommended Water
Application Viscosity Add water approximately one to one volume of paint
Method of Application By brush
Subsequent Coat Distemper & Plastic Emulsion Paint
Packing 20 litres, 10 litres, 4 litres, 1 litres & 500 mls.

Chamak Acrylic Primer (Water Base) water thinable is used for priming plastered walls, bricks, asbestos, concrete to give wall alkali resistance, good sealing properties, fast setting & good brushing. It is also fungus resistance. It can be thinned with water to application viscosity.

Recommended Use:
  • Plastered walls, bricks, asbestos, concrete. It can be used as a water base primer for subsequent coats of distemper & plastic emulsion paint.

Drying Time:
  • Surface Dry - Less than 30 minutes.
  • Hard Dry - Less than 16 hours
  • Overcoat time - Minimum 4 to 5 hours.

Covering Capacity on Smooth Surface:
  • 15 to 18 sq. mt. / lit. / coat for 15 to 18 micron dry film thickness depending upon surface & surface preparation by brushing.

Direction for Use:
  • Remove all loose flakes. Previous paint should be stripped off. Apply one or two coats of primer by adding appropriate quantity of water by brush. Allow prime coat to hard dry. Dry cut with sand paper before applying subsequent coat's. Stir well prior to use.
Yes! I am interested

Anticorrosive Bituminous Black/Black Japan Paint (IS 158)

REQUEST CALLBACK

Anticorrosive Bituminous Black/Black Japan Paint (IS 158)
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
FinishSmooth and Glossy
ColorBlack
Covering Capacity11 to 13 sq. mt. / lit. / Coat for 25 micron dry film thickness
Solid Content45 + 3%
Flash PointAbove 30 deg C (86 deg F)
Thinner RecommendedSynthetic G.P. Thinner
Method of ApplicationBrushing or spraying at a pressure of 40 to 50 P.S.I.
Packing20 litres,10 litres,4 litre

It is an anticorrosive paint for iron and steel because it is waterproof and impermeable. It is chemically inert & hence it is resistant to attack on metallic surface from corrosion.

Recommended Use:
  • It is recommended for protection of iron and steel structures from corrosion and where alkali and acid resistance are required to a certain extent.

Drying Time:
  • Surface dry - 1 hours maximum
  • Hard dry - 16 hours maximum

Direction for Use:
  • Surface should be free from rust, dirt, grease, oil, moisture and loose flakes. Apply by brush or spray. Use recommended thinner, if required.
Yes! I am interested

Zinc Chrome Primer to IS 104

REQUEST CALLBACK

Zinc Chrome Primer to IS 104
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Finish Smooth and matt to egg shell
ColorYellow
Flash Point Above 30 deg C (86 deg F)
Thinner Recommended Synthetic G.P. Thinner
Method of ApplicationBy brush or spray at a pressure of 40 to 50 PSI.
Overcoating Finish It can be overcoated with conventional product and Chlorinated Rubber Paint
Packing 20 litres, 4 litres, 1 litre & 500 mls.

This is single pack air drying, based on Syn. Resins and contains corrosion inhabiting pigments such as Zinc Chrome. It has very good anti corrosive property.

Recommended Use:
  • Protection of aluminum alloy / metal, structural steel, conveyors, storage tanks, etc.

Covering Capacity on Smooth Mild Steel Surface:
  • 10 to 11 sq. mt. / lt. for 25 micron dry film thickness.

Drying Time:
  • Surface Dry - Less than 30 minutes.
  • Hard Dry - Less than 16 hours.

Direction for Use:
  • Ensure that surface should be free from rust, grease, oil, moisture and other loose flakes. Apply by brush or spray after adjusting to brushing or spraying viscosity by recommended thinner. Allow the primer coat to hard dry before applying finishing coat. Stir well before use. For galvanised steel and non, ferrous metals pretreat with Wash Primer, followed by one coat of Chamak Zinc Chromate Primer.

Storage Life:
  • As long as containers are kept sealed, it can be stored up to twelve months without deterioration.
Yes! I am interested

Epoxy Thinner

REQUEST CALLBACK

Epoxy Thinner
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorWater White
Flash Point Above 25 deg C (75 deg F).
Specific Gravity 0.8 + 0.02 at 30 deg C.
Recommended for For thinning all types of Chamak Epoxy Paints, Primers, etc.
Packing 20 liters, 10 liters, 5 liters & 1 liters.

It is added in Epoxy to obtain a consistency suitable for application. As a general rule, thinning should be kept at a minimum as the quality of the paint work will suffer from too liberal thinning. This thinner is blended to give the best results with regard to spray, brush finishing properties etc.
Yes! I am interested

Stoving Thinner

REQUEST CALLBACK

Stoving Thinner
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorWater White
Flash Point Above 25 deg C (75 deg F).
Specific Gravity 0.8 + 0.02 at 30 deg C
Recommended for For thinning Chamak Stoving Enamels, A.D. cum Stoving Enamels etc.
Packing 20 liters, 10 liters, 5 liters & 1 liters.

It is added in Stoving paints to obtain a consistency suitable for application. As a general rule, thinning should be kept at a minimum as the quality of the paint work will suffer from too liberal thinning. This thinner is blended to give the best results with regard to spray finishing properties etc.
Yes! I am interested

Synthetic Thinner

REQUEST CALLBACK

Synthetic Thinner
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Flash PointAbove 30 deg C (86 deg F).
Colour Water White
Specific Gravity 0.780 + 0.02 at 30 deg C.
Recommended for For thinning Synthetic Enamels, Chamak Primer etc.
Packing 20 liters, 10 liters, 5 liters & 1 liters

This is a general Purpose Thinner. It is added in synthetic paints to obtain a consistency suitable for application. As a general rule, thinning should be kept at a minimum as the quality of the paint work will suffer from too liberal thinning. This thinner is blended to give the best result with regard to brushability, spray finishing properties etc.
Yes! I am interested

PU Thinner

REQUEST CALLBACK

PU Thinner
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
ColorWater White
Flash PointAbove 25 deg C (75deg F)
Specific Gravity 0.84+-0.02at -30 deg C
Recommended for For thinning all types of chamak polyrethane paints, primer and clear etc
Packing 20 lit, 10 lit, 5 lit, 1 lit.

It is added in polyurethane paint to Obtain A Consistency Suitable for Application, As A General Rule, Thinning Should be Kept At A Minimum as the quality of the paint work will suffer from too liberal thinning. This Thinner is blended to give the best results with regard to spray, brush finishing properties etc.
Yes! I am interested

Paint Remover

REQUEST CALLBACK

Paint Remover
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Physical StateLiquid
UsageBuilding Coating
Packaging Size4 lit, 1 lit, 500 ml

Chamak paint remover is specially developed for removing any kind of paints. It removes paints very quickly and easily.

Precautions:
  • Store in a cool, dry & ventilated place away from heat
  • Shake well before use
  • Take care while opening.
  • Wear safety goggles during use.
  • Wear PVC hand gloves while applying.
  • Incase of accident flush the affected area white plenty of water.

Application:
  • Automobiles plants
  • Chemical & Cold storage plants
  • Cotton jute & Wooden mills
  • Garrage
  • Engineering works
  • Power station
  • Railways
  • Refineries
  • Ship braking yard
  • Tea estates etc.

Direction for Use:
  • This Product can be applied bay different method like brushing or dipping.
  • Use wire brush or metal plat to clean the surface.
Yes! I am interested

Rust Remover

REQUEST CALLBACK

Rust Remover
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Product Details:
Pack Size20 lit, 10 lit, 5 lit, 1 lit
Color Water White
Recommended for All types of rusted surface

This is specialised product from Chamak. Chamak Rust Remover is specially developed for removing rust from any surface. It removes rust easily.

Precautions:
  • Store in a cool, dry & ventilated area shake well before use.
  • Take care while opening.
  • Wear PVC hand gloves while applying.
  • In case of accident flush the affected area with plent of water.

Direction:
  • Sand and clean the surface free from loose dust and other loose flakes
  • Apply Chamak Rust remover by brush. When surface is free from rust, clean the surface from water & cloth.
Yes! I am interested

 
X


Explore More Products

Contact via E-mail
Contact via SMS
Chamak Paint Industries
Dharmendra Kanani (Sales Head)
Thakkarbapa Nagar, National Highway No. 8 Block No. 1471,
Ahmedabad - 382350, Gujarat, India
Call Us: 
Call Response Rate: 89%
Share Us :
F G T L



Home  |   Profile   |  Our Products  |  Site Map  |   Contact Us

© Chamak Paint Industries. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited

Chamak Paint Industries